[srslte-users] srslte-users Digest, Vol 29, Issue 6

Robson Pereira robson.apereira at gmail.com
Fri Jul 7 18:27:07 UTC 2017


Hi Justin,

Yes, it looks like pdsch_ue example is working as it has the same behavior
for both LimeSDR and USRP B210:

(I need to find a proper cell)

  Searching for cell...
  Could not find any cell in this frequency
  Cell not found after 0 trials. Trying again (Press Ctrl+C to exit)

Thanks,
Robson




On Fri, Jul 7, 2017 at 3:20 AM, Justin Tallon <
justin.tallon at softwareradiosystems.com> wrote:

> Hey Robson!
>
> Are you able to find the Lime Device by running "SoapySDRUtil --find " ?
>
> If so, are you able to run the pdsch_ue example?
>
>
> ____
> Justin Tallon Ph.D.
>
> Software Radio Systems (SRS)
> http://www.softwareradiosystems.com
>
> +353-86-067-0753 <+353%2086%20067%200753> | justin.tallon@
> softwareradiosystems.com
>
> On Fri, Jul 7, 2017 at 6:28 AM, Robson Pereira <robson.apereira at gmail.com>
> wrote:
>
>> I get errors with LimeSDR while it works with USRP B210. I'm not sure if
>> this is a known issue...
>>
>>
>> ~/srsLTE/build/lib/examples$ *./cell_search -b 20*
>> < ... >
>> Uploading DC/IQ calibration firmware
>> -- L
>> MCU Ref. clock: 30.72 MHz
>> MCU algorithm time: 215 ms
>> *Error code 0x1 was returned during streaming. Aborting.*
>> *Error code 0x1 was returned during streaming. Aborting.*
>>
>>
>> ~/srsLTE/build/srsue/src$ *sudo ./srsue ue.conf.example*
>> < ... >
>> Rx calibration using RSSI INTERNAL ON BOARD loopback
>> Rx ch.A @ 2685 MHz, BW: 30 MHz, RF input: LNAL, PGA: 20, LNA: 15, TIA: 3
>> Rx calibration: using cached values
>> Rx calibration values found in cache:
>> | DC | GAIN | PHASE
>> ---+-----+------+------
>> I: | 0 | 2047 | 0
>> Q: | 0 | 2047 |
>>
>> *Searching for cell...*
>> *Searching for cell...*
>>
>> On Thu, Jul 6, 2017 at 7:13 AM, <srslte-users-request at lists.so
>> ftwareradiosystems.com> wrote:
>>
>>> Send srslte-users mailing list submissions to
>>>         srslte-users at lists.softwareradiosystems.com
>>>
>>> To subscribe or unsubscribe via the World Wide Web, visit
>>>         http://www.softwareradiosystems.com/mailman/listinfo/srslte-
>>> users
>>> or, via email, send a message with subject or body 'help' to
>>>         srslte-users-request at lists.softwareradiosystems.com
>>>
>>> You can reach the person managing the list at
>>>         srslte-users-owner at lists.softwareradiosystems.com
>>>
>>> When replying, please edit your Subject line so it is more specific
>>> than "Re: Contents of srslte-users digest..."
>>>
>>> Today's Topics:
>>>
>>>    1. Re: limeSDR (Johann T.)
>>>
>>>
>>> ---------- Forwarded message ----------
>>> From: "Johann T." <johann.tzt at gmail.com>
>>> To: Justin Tallon <justin.tallon at softwareradiosystems.com>
>>> Cc: srslte-users at lists.softwareradiosystems.com
>>> Bcc:
>>> Date: Thu, 6 Jul 2017 16:20:47 +0200
>>> Subject: Re: [srslte-users] limeSDR
>>> Hi Justin,
>>>
>>> The SoapySDRUtil was not available. I guess I haven't fully installed
>>> the SoapySDR. I only ran "sudo apt-get install libsoapysdr-dev". My
>>> bad, sorry!
>>>
>>> It worked fine after I ran this command:
>>>
>>> sudo apt-get install soapysdr soapysdr-module-lms7
>>>
>>> Here is the output of SoapySDRUtil --find
>>>
>>> tno at snowwhite:~/test/srsLTE/build/lib/examples$ SoapySDRUtil --find
>>> ######################################################
>>> ## Soapy SDR -- the SDR abstraction library
>>> ######################################################
>>>
>>> Found device 0
>>>   addr = 1d50:6108
>>>   driver = lime
>>>   label = LimeSDR-USB [USB 3.0] 9062000C50C0D
>>>   media = USB 3.0
>>>   module = STREAM
>>>   name = LimeSDR-USB
>>>   serial = 0009062000C50C0D
>>>
>>> I could run the cell_search now, but the output was not as expected.
>>> There is an error while calling srslte_ue_sync_work(). Any ideas what went
>>> wrong?
>>>
>>> Thanks,
>>> Johann
>>>
>>>
>>>
>>> ------------------------------------------------------------
>>> --------------------------------------------------------
>>>
>>> tno at snowwhite:~/test/srsLTE/build/lib/examples$ ./cell_search -b 20
>>> linux; GNU C++ version 5.4.0 20160609; Boost_105800;
>>> UHD_003.010.001.001-release
>>>
>>> Opening RF device...
>>> Opening USRP with args:
>>> Error opening UHD: code 11
>>> Soapy Has Found device #0: addr=1d50:6108, driver=lime,
>>> label=LimeSDR-USB [USB 3.0] 9062000C50C0D, media=USB 3.0, module=STREAM,
>>> name=LimeSDR-USB, serial=0009062000C50C0D,
>>> [INFO] Make connection: 'LimeSDR-USB [USB 3.0] 9062000C50C0D'
>>> [INFO] Estimated reference clock 30.7197 MHz
>>> [INFO] Selected reference clock 30.720 MHz
>>> [INFO] Device name: LimeSDR-USB
>>> [INFO] Reference: 30.72 MHz
>>> [INFO] Init LMS7002M(0)
>>> [INFO] LMS7002M cache /home/tno/.limesuite/LMS7002M_cache_values.db
>>> [INFO] Ver=7, Rev=1, Mask=1
>>> [INFO] LMS7002M calibration values caching Enable
>>> CGEN: Freq=80 MHz, VCO=2.56 GHz, INT=82, FRAC=349525, DIV_OUTCH_CGEN=15
>>> M=156, N=3, Fvco=1040.000 MHz
>>> 16: FE AF AA
>>> 16: AA AA 7C
>>> phase: min 26.0; max 197.3; selected 111.6)
>>> M=156, N=3, Fvco=1040.000 MHz
>>> M=182, N=7, Fvco=1040.000 MHz
>>> 16: AA 5A 75
>>> 16: AA 52 D5
>>> phase: min 10.4; max 176.5; selected 93.5)
>>> M=182, N=7, Fvco=1040.000 MHz
>>> M=156, N=3, Fvco=1040.000 MHz
>>> 16: FE AF AA
>>> 16: AA AA 3C
>>> phase: min 26.0; max 197.3; selected 111.6)
>>> M=156, N=3, Fvco=1040.000 MHz
>>> M=156, N=3, Fvco=1040.000 MHz
>>> 16: 57 AD 3B
>>> 16: 26 DC 3D
>>> 19: AA 5A 75
>>> 16: AA 52 D5
>>> phase: min 20.8; max 176.5; selected 98.7)
>>> M=156, N=3, Fvco=1040.000 MHz
>>> [INFO] Rx Filter calibrated from cache
>>> [INFO] Tx Filter calibrated from cache
>>> M=156, N=3, Fvco=1040.000 MHz
>>> phase: min 5.2; max 360.0; selected 182.6)
>>> M=156, N=3, Fvco=1040.000 MHz
>>> M=182, N=7, Fvco=1040.000 MHz
>>> phase: min 5.2; max 360.0; selected 182.6)
>>> M=182, N=7, Fvco=1040.000 MHz
>>> M=156, N=3, Fvco=1040.000 MHz
>>> phase: min 5.2; max 360.0; selected 182.6)
>>> M=156, N=3, Fvco=1040.000 MHz
>>> M=156, N=3, Fvco=1040.000 MHz
>>> phase: min 5.2; max 360.0; selected 182.6)
>>> M=156, N=3, Fvco=1040.000 MHz
>>> [INFO] Rx Filter calibrated from cache
>>> [INFO] Tx Filter calibrated from cache
>>> SetFrequency using cache values vco:1, csw:206
>>> TODO: implement rf_soapy_rx_wait_lo_locked()
>>> [  0/299]: EARFCN 6150 Freq. 791.00 MHz looking for PSS.
>>> Using Volk machine: avx2_64_mmx_orc
>>> CGEN: Freq=245.76 MHz, VCO=2.4576 GHz, INT=79, FRAC=0, DIV_OUTCH_CGEN=4
>>> ############################################################
>>> Rx calibration using RSSI INTERNAL ON BOARD loopback
>>> Rx ch.A @  791 MHz, BW: 30 MHz, RF input: LNAL, PGA: 31, LNA: 15, TIA: 3
>>> Rx calibration: using cached values
>>> Rx calibration values found in cache:
>>>    | DC  | GAIN | PHASE
>>> ---+-----+------+------
>>> I: |   0 | 2047 | 0
>>> Q: |   0 | 2047 |
>>> ############################################################
>>> SetFrequency using cache values vco:1, csw:206
>>> TODO: implement rf_soapy_rx_wait_lo_locked()
>>> [  1/299]: EARFCN 6151 Freq. 791.10 MHz looking for PSS.
>>> ############################################################
>>> Rx calibration using RSSI INTERNAL ON BOARD loopback
>>> Rx ch.A @ 791.1 MHz, BW: 30 MHz, RF input: LNAL, PGA: 31, LNA: 15, TIA: 3
>>> Rx calibration: using cached values
>>> Rx calibration values found in cache:
>>>    | DC  | GAIN | PHASE
>>> ---+-----+------+------
>>> I: |   0 | 2047 | 0
>>> Q: |   0 | 2047 |
>>> ############################################################
>>> Rx pktLoss: ts diff: 17680  pktLoss: 12
>>> SetFrequency using cache values vco:1, csw:206
>>> TODO: implement rf_soapy_rx_wait_lo_locked()
>>> [  2/299]: EARFCN 6152 Freq. 791.20 MHz looking for PSS.
>>> ############################################################
>>> Rx calibration using RSSI INTERNAL ON BOARD loopback
>>> Rx ch.A @ 791.2 MHz, BW: 30 MHz, RF input: LNAL, PGA: 31, LNA: 15, TIA: 3
>>> Rx calibration: using cached values
>>> Rx calibration values found in cache:
>>>    | DC  | GAIN | PHASE
>>> ---+-----+------+------
>>> I: |   0 | 2047 | 0
>>> Q: |   0 | 2047 |
>>> ############################################################
>>> Rx pktLoss: ts diff: 20400  pktLoss: 14
>>> SetFrequency using cache values vco:1, csw:206
>>> TODO: implement rf_soapy_rx_wait_lo_locked()
>>> [  3/299]: EARFCN 6153 Freq. 791.30 MHz looking for PSS.
>>> ############################################################
>>> Rx calibration using RSSI INTERNAL ON BOARD loopback
>>> Rx ch.A @ 791.3 MHz, BW: 30 MHz, RF input: LNAL, PGA: 31, LNA: 15, TIA: 3
>>> Rx calibration: using cached values
>>> Rx calibration values found in cache:
>>>    | DC  | GAIN | PHASE
>>> ---+-----+------+------
>>> I: |   0 | 2047 | 0
>>> Q: |   0 | 2047 |
>>> ############################################################
>>> Rx pktLoss: ts diff: 20400  pktLoss: 14
>>> SetFrequency using cache values vco:1, csw:206
>>> TODO: implement rf_soapy_rx_wait_lo_locked()
>>> [  4/299]: EARFCN 6154 Freq. 791.40 MHz looking for PSS.
>>> ############################################################
>>> Rx calibration using RSSI INTERNAL ON BOARD loopback
>>> Rx ch.A @ 791.4 MHz, BW: 30 MHz, RF input: LNAL, PGA: 31, LNA: 15, TIA: 3
>>> Rx calibration: using cached values
>>> Rx calibration values found in cache:
>>>    | DC  | GAIN | PHASE
>>> ---+-----+------+------
>>> I: |   0 | 2047 | 0
>>> Q: |   0 | 2047 |
>>> ############################################################
>>> [INFO] L 1447040
>>> Rx pktLoss: ts diff: 20400  pktLoss: 14
>>> SetFrequency using cache values vco:1, csw:206
>>> TODO: implement rf_soapy_rx_wait_lo_locked()
>>> [  5/299]: EARFCN 6155 Freq. 791.50 MHz looking for PSS.
>>> ############################################################
>>> Rx calibration using RSSI INTERNAL ON BOARD loopback
>>> Rx ch.A @ 791.5 MHz, BW: 30 MHz, RF input: LNAL, PGA: 31, LNA: 15, TIA: 3
>>> Rx calibration: using cached values
>>> Rx calibration values found in cache:
>>>    | DC  | GAIN | PHASE
>>> ---+-----+------+------
>>> I: |   0 | 2047 | 0
>>> Q: |   0 | 2047 |
>>> ############################################################
>>> Rx pktLoss: ts diff: 20400  pktLoss: 14
>>> Rx: 5.500 MB/s
>>> TODO: implement rf_soapy_rx_wait_lo_locked()
>>> [  6/299]: EARFCN 6156 Freq. 791.60 MHz looking for PSS.
>>> ############################################################
>>> Rx calibration using RSSI INTERNAL ON BOARD loopback
>>> Rx ch.A @ 791.6 MHz, BW: 30 MHz, RF input: LNAL, PGA: 31, LNA: 15, TIA: 3
>>> Performed by: MCU
>>> ------------------------------------------------------------
>>> MCU algorithm time: 10 ms
>>> Current MCU firmware: 127, unknown
>>> Uploading DC/IQ calibration firmware
>>> MCU programming : 16384/16384
>>> MCU Programming finished, 827 ms
>>> MCU Ref. clock: 30.72 MHz
>>> Rx: 0.589 MB/s
>>> MCU algorithm time: 208 ms
>>> Rx: 0.066 MB/s
>>> Rx: 0.000 MB/s
>>> Error receiving samples
>>> Error calling srslte_ue_sync_work()
>>> Rx: 0.000 MB/s
>>> Error receiving samples
>>> Error calling srslte_ue_sync_work()
>>> Rx: 0.000 MB/s
>>> Error receiving samples
>>> Error calling srslte_ue_sync_work()
>>> TODO: implement rf_soapy_rx_wait_lo_locked()
>>> [  7/299]: EARFCN 6157 Freq. 791.70 MHz looking for PSS.
>>> ############################################################
>>> Rx calibration using RSSI INTERNAL ON BOARD loopback
>>> Rx ch.A @ 791.7 MHz, BW: 30 MHz, RF input: LNAL, PGA: 31, LNA: 15, TIA: 3
>>> Performed by: MCU
>>> ------------------------------------------------------------
>>> MCU algorithm time: 1 ms
>>> Current MCU firmware: 3, DC/IQ calibration full
>>> MCU Ref. clock: 30.72 MHz
>>> MCU algorithm time: 208 ms
>>> Rx pktLoss: ts diff: 34000  pktLoss: 24
>>> Rx pktLoss: ts diff: 2129760  pktLoss: 1565
>>> Rx: 0.426 MB/s
>>> ^CSIGINT received. Exiting...
>>> Rx: 0.000 MB/s
>>> Error receiving samples
>>> Error calling srslte_ue_sync_work()
>>> Rx: 0.000 MB/s
>>> Error receiving samples
>>> Error calling srslte_ue_sync_work()
>>>
>>>
>>> Found 0 cells
>>>
>>> Bye
>>>
>>>
>>>
>>>
>>> On Thu, Jul 6, 2017 at 3:49 PM, Justin Tallon <
>>> justin.tallon at softwareradiosystems.com> wrote:
>>>
>>>> Hey Johann!
>>>>
>>>> Could you try run  :
>>>>
>>>> SoapySDRUtil --find
>>>>
>>>> from your command line and see if it finds your device?
>>>>
>>>> Regards,
>>>> Justin
>>>>
>>>> ____
>>>> Justin Tallon Ph.D.
>>>>
>>>> Software Radio Systems (SRS)
>>>> http://www.softwareradiosystems.com
>>>>
>>>> +353-86-067-0753 <+353%2086%20067%200753> |
>>>> justin.tallon at softwareradiosystems.com
>>>>
>>>> On Thu, Jul 6, 2017 at 1:42 PM, Johann T. <johann.tzt at gmail.com> wrote:
>>>>
>>>>> Hi Justin,
>>>>>
>>>>> Thanks for your quick response.
>>>>>
>>>>> I attached here the output from the cmake. It seemed that the soapySDR
>>>>> module was properly detected.
>>>>>
>>>>> Regards,
>>>>> Johann
>>>>>
>>>>>
>>>>>
>>>>> On Thu, Jul 6, 2017 at 11:13 AM, Justin Tallon <
>>>>> justin.tallon at softwareradiosystems.com> wrote:
>>>>>
>>>>>> Hey Johann!
>>>>>>
>>>>>> Could you possibly delete CMakeCache.txt from your build directory
>>>>>> and run cmake again and send me the terminal output?
>>>>>>
>>>>>> Thanks!
>>>>>> Justin
>>>>>>
>>>>>> ____
>>>>>> Justin Tallon Ph.D.
>>>>>>
>>>>>> Software Radio Systems (SRS)
>>>>>> http://www.softwareradiosystems.com
>>>>>>
>>>>>> +353-86-067-0753 <+353%2086%20067%200753> |
>>>>>> justin.tallon at softwareradiosystems.com
>>>>>>
>>>>>> On Thu, Jul 6, 2017 at 9:56 AM, Johann T. <johann.tzt at gmail.com>
>>>>>> wrote:
>>>>>>
>>>>>>> Hi,
>>>>>>>
>>>>>>> Previously I have used srslte with USRP B210 and it worked
>>>>>>> perfectly. I have just received my limeSDR and I would like to use srslte
>>>>>>> with it.
>>>>>>>
>>>>>>> I have followed the installation procedures as described in this
>>>>>>> thread. The cmake and make were completed without errors and the
>>>>>>> libSoapySDR.so is there in the /usr/lib/x86_64-linux-gnu/ folder.
>>>>>>> However, when I started the cell_search example, it complained that no
>>>>>>> compatible device was found.
>>>>>>>
>>>>>>> Any suggestions what could be the issue? Do I need to change
>>>>>>> something in the code?
>>>>>>>
>>>>>>> Many thanks!
>>>>>>>
>>>>>>> Regards,
>>>>>>> Johann
>>>>>>>
>>>>>>> PS: Both examples from the LimeSuiteGUI worked fine and my machine
>>>>>>> is running Ubuntu 16.04.
>>>>>>>
>>>>>>>
>>>>>>> On Wed, Jun 14, 2017 at 5:20 PM, Justin Tallon <
>>>>>>> justin.tallon at softwareradiosystems.com> wrote:
>>>>>>>
>>>>>>>> no problem!
>>>>>>>>
>>>>>>>> Justin
>>>>>>>>
>>>>>>>> ____
>>>>>>>> Justin Tallon Ph.D.
>>>>>>>>
>>>>>>>> Software Radio Systems (SRS)
>>>>>>>> http://www.softwareradiosystems.com
>>>>>>>>
>>>>>>>> +353-86-067-0753 <+353%2086%20067%200753> |
>>>>>>>> justin.tallon at softwareradiosystems.com
>>>>>>>>
>>>>>>>> On Wed, Jun 14, 2017 at 4:20 PM, Nicola Bui <nicola.bui at imdea.org>
>>>>>>>> wrote:
>>>>>>>>
>>>>>>>>> You are right. It worked.
>>>>>>>>> I was looking for soapysdr-dev, that's why I could not find it.
>>>>>>>>>
>>>>>>>>> Thanks,
>>>>>>>>>
>>>>>>>>> Nicola Bui
>>>>>>>>>
>>>>>>>>> Research Engineer
>>>>>>>>> IMDEA Networks Institute
>>>>>>>>> Av. Mar del Mediterraneo, 22
>>>>>>>>> 28918 - Leganés (Madrid) - Spain
>>>>>>>>> mobile: +34 657 633 987 <+34%20657%2063%2039%2087>
>>>>>>>>> phone: +34 91 481 6986 <+34%20914%2081%2069%2086>
>>>>>>>>> fax: +34 481 6965
>>>>>>>>>
>>>>>>>>> On Wed, Jun 14, 2017 at 11:17 AM, Justin Tallon <
>>>>>>>>> justin.tallon at softwareradiosystems.com> wrote:
>>>>>>>>>
>>>>>>>>>> Cool,
>>>>>>>>>>
>>>>>>>>>> Could you try run
>>>>>>>>>>
>>>>>>>>>> sudo apt-get install libsoapysdr-dev
>>>>>>>>>>
>>>>>>>>>> and then delete your CMakeCache.txt file from your build folder
>>>>>>>>>> and re run cmake ?
>>>>>>>>>>
>>>>>>>>>> Thanks!
>>>>>>>>>>
>>>>>>>>>> Justin
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>> ____
>>>>>>>>>> Justin Tallon Ph.D.
>>>>>>>>>>
>>>>>>>>>> Software Radio Systems (SRS)
>>>>>>>>>> http://www.softwareradiosystems.com
>>>>>>>>>>
>>>>>>>>>> +353-86-067-0753 <+353%2086%20067%200753> |
>>>>>>>>>> justin.tallon at softwareradiosystems.com
>>>>>>>>>>
>>>>>>>>>> On Wed, Jun 14, 2017 at 4:15 PM, Nicola Bui <nicola.bui at imdea.org
>>>>>>>>>> > wrote:
>>>>>>>>>>
>>>>>>>>>>> Here you are:
>>>>>>>>>>>
>>>>>>>>>>> sudo add-apt-repository -y ppa:myriadrf/drivers
>>>>>>>>>>> sudo apt-get update
>>>>>>>>>>> sudo apt-get install limesuite limesuite-udev limesuite-images
>>>>>>>>>>> sudo apt-get install soapysdr soapysdr-module-lms7
>>>>>>>>>>>
>>>>>>>>>>>
>>>>>>>>>>> Nicola Bui
>>>>>>>>>>>
>>>>>>>>>>> Research Engineer
>>>>>>>>>>> IMDEA Networks Institute
>>>>>>>>>>> Av. Mar del Mediterraneo, 22
>>>>>>>>>>> 28918 - Leganés (Madrid) - Spain
>>>>>>>>>>> mobile: +34 657 633 987 <+34%20657%2063%2039%2087>
>>>>>>>>>>> phone: +34 91 481 6986 <+34%20914%2081%2069%2086>
>>>>>>>>>>> fax: +34 481 6965
>>>>>>>>>>>
>>>>>>>>>>> On Wed, Jun 14, 2017 at 11:13 AM, Justin Tallon <
>>>>>>>>>>> justin.tallon at softwareradiosystems.com> wrote:
>>>>>>>>>>>
>>>>>>>>>>>> I believe that there is also meant to be a libSoapySDR.so file
>>>>>>>>>>>> present alongside them.
>>>>>>>>>>>>
>>>>>>>>>>>> Can you recall all the apt-get commands that you have used to
>>>>>>>>>>>> install Soapy?
>>>>>>>>>>>>
>>>>>>>>>>>>
>>>>>>>>>>>> ____
>>>>>>>>>>>> Justin Tallon Ph.D.
>>>>>>>>>>>>
>>>>>>>>>>>> Software Radio Systems (SRS)
>>>>>>>>>>>> http://www.softwareradiosystems.com
>>>>>>>>>>>>
>>>>>>>>>>>> +353-86-067-0753 <+353%2086%20067%200753> |
>>>>>>>>>>>> justin.tallon at softwareradiosystems.com
>>>>>>>>>>>>
>>>>>>>>>>>> On Wed, Jun 14, 2017 at 4:09 PM, Nicola Bui <
>>>>>>>>>>>> nicola.bui at imdea.org> wrote:
>>>>>>>>>>>>
>>>>>>>>>>>>> Yes, it is. But the name is libSoapySDR.so.0.6 or
>>>>>>>>>>>>> libSoapySDR.so.0.6.0.
>>>>>>>>>>>>> Is it just a bad link?
>>>>>>>>>>>>>
>>>>>>>>>>>>> Nicola Bui
>>>>>>>>>>>>>
>>>>>>>>>>>>> Research Engineer
>>>>>>>>>>>>> IMDEA Networks Institute
>>>>>>>>>>>>> Av. Mar del Mediterraneo, 22
>>>>>>>>>>>>> 28918 - Leganés (Madrid) - Spain
>>>>>>>>>>>>> mobile: +34 657 633 987 <+34%20657%2063%2039%2087>
>>>>>>>>>>>>> phone: +34 91 481 6986 <+34%20914%2081%2069%2086>
>>>>>>>>>>>>> fax: +34 481 6965
>>>>>>>>>>>>>
>>>>>>>>>>>>> On Wed, Jun 14, 2017 at 11:06 AM, Justin Tallon <
>>>>>>>>>>>>> justin.tallon at softwareradiosystems.com> wrote:
>>>>>>>>>>>>>
>>>>>>>>>>>>>> Hey Nicola!
>>>>>>>>>>>>>>
>>>>>>>>>>>>>> Can you confirm that the libSoapySDR.so is present in your
>>>>>>>>>>>>>> /usr/lib/ or /usr/lib/x86_64-linux-gnu/ folder ?
>>>>>>>>>>>>>>
>>>>>>>>>>>>>> I would not recommend installing source versions on top of
>>>>>>>>>>>>>> binary installations as this can cause conflicts that produce problems down
>>>>>>>>>>>>>> the line.
>>>>>>>>>>>>>>
>>>>>>>>>>>>>> Justin
>>>>>>>>>>>>>>
>>>>>>>>>>>>>> ____
>>>>>>>>>>>>>> Justin Tallon Ph.D.
>>>>>>>>>>>>>>
>>>>>>>>>>>>>> Software Radio Systems (SRS)
>>>>>>>>>>>>>> http://www.softwareradiosystems.com
>>>>>>>>>>>>>>
>>>>>>>>>>>>>> +353-86-067-0753 <+353%2086%20067%200753> |
>>>>>>>>>>>>>> justin.tallon at softwareradiosystems.com
>>>>>>>>>>>>>>
>>>>>>>>>>>>>> On Wed, Jun 14, 2017 at 3:57 PM, Nicola Bui <
>>>>>>>>>>>>>> nicola.bui at imdea.org> wrote:
>>>>>>>>>>>>>>
>>>>>>>>>>>>>>> Hi,
>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>> I installed soapy, too.
>>>>>>>>>>>>>>> The cmake log is attached.
>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>> Thanks,
>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>> Nicola Bui
>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>> Research Engineer
>>>>>>>>>>>>>>> IMDEA Networks Institute
>>>>>>>>>>>>>>> Av. Mar del Mediterraneo, 22
>>>>>>>>>>>>>>> 28918 - Leganés (Madrid) - Spain
>>>>>>>>>>>>>>> mobile: +34 657 633 987 <+34%20657%2063%2039%2087>
>>>>>>>>>>>>>>> phone: +34 91 481 6986 <+34%20914%2081%2069%2086>
>>>>>>>>>>>>>>> fax: +34 481 6965
>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>> On Wed, Jun 14, 2017 at 10:50 AM, Justin Tallon <
>>>>>>>>>>>>>>> justin.tallon at softwareradiosystems.com> wrote:
>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>> Hey Nicola!
>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>> Could you post the output of your cmake ?
>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>> Thanks!
>>>>>>>>>>>>>>>> Justin
>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>> On 14 Jun 2017 5:41 p.m., "Nicola Bui" <
>>>>>>>>>>>>>>>> nicola.bui at imdea.org> wrote:
>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>> Dear all,
>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>> I am trying to make srsLTE work with LimeSDR, but cmake
>>>>>>>>>>>>>>>>> does not find the LimeSuite package.
>>>>>>>>>>>>>>>>> I am running it on a ubuntu 16.04 pc, limesuite is
>>>>>>>>>>>>>>>>> installed and I correctly went through the tutorial examples of the
>>>>>>>>>>>>>>>>> LimeSuiteGui (both the selfloop and the reception).
>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>> Any suggestions before I am trying installing limesuite
>>>>>>>>>>>>>>>>> from the sources?
>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>> Thanks,
>>>>>>>>>>>>>>>>> Nicola Bui
>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>> Research Engineer
>>>>>>>>>>>>>>>>> IMDEA Networks Institute
>>>>>>>>>>>>>>>>> Av. Mar del Mediterraneo, 22
>>>>>>>>>>>>>>>>> 28918 - Leganés (Madrid) - Spain
>>>>>>>>>>>>>>>>> mobile: +34 657 633 987 <+34%20657%2063%2039%2087>
>>>>>>>>>>>>>>>>> phone: +34 91 481 6986 <+34%20914%2081%2069%2086>
>>>>>>>>>>>>>>>>> fax: +34 481 6965
>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>> _______________________________________________
>>>>>>>>>>>>>>>>> srslte-users mailing list
>>>>>>>>>>>>>>>>> srslte-users at lists.softwareradiosystems.com
>>>>>>>>>>>>>>>>> http://www.softwareradiosystem
>>>>>>>>>>>>>>>>> s.com/mailman/listinfo/srslte-users
>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>
>>>>>>>>>>>>>
>>>>>>>>>>>>
>>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>
>>>>>>>>
>>>>>>>> _______________________________________________
>>>>>>>> srslte-users mailing list
>>>>>>>> srslte-users at lists.softwareradiosystems.com
>>>>>>>> http://www.softwareradiosystems.com/mailman/listinfo/srslte-users
>>>>>>>>
>>>>>>>>
>>>>>>>
>>>>>>> _______________________________________________
>>>>>>> srslte-users mailing list
>>>>>>> srslte-users at lists.softwareradiosystems.com
>>>>>>> http://www.softwareradiosystems.com/mailman/listinfo/srslte-users
>>>>>>>
>>>>>>>
>>>>>>
>>>>>
>>>>
>>>
>>> _______________________________________________
>>> srslte-users mailing list
>>> srslte-users at lists.softwareradiosystems.com
>>> http://www.softwareradiosystems.com/mailman/listinfo/srslte-users
>>>
>>>
>>
>> _______________________________________________
>> srslte-users mailing list
>> srslte-users at lists.softwareradiosystems.com
>> http://www.softwareradiosystems.com/mailman/listinfo/srslte-users
>>
>>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://www.softwareradiosystems.com/pipermail/srslte-users/attachments/20170707/6e21f0f6/attachment-0001.html>


More information about the srslte-users mailing list