[srslte-users] srslte-users Digest, Vol 29, Issue 6

Justin Tallon justin.tallon at softwareradiosystems.com
Fri Jul 7 10:20:18 UTC 2017


Hey Robson!

Are you able to find the Lime Device by running "SoapySDRUtil --find " ?

If so, are you able to run the pdsch_ue example?


____
Justin Tallon Ph.D.

Software Radio Systems (SRS)
http://www.softwareradiosystems.com

+353-86-067-0753 | justin.tallon at softwareradiosystems.com

On Fri, Jul 7, 2017 at 6:28 AM, Robson Pereira <robson.apereira at gmail.com>
wrote:

> I get errors with LimeSDR while it works with USRP B210. I'm not sure if
> this is a known issue...
>
>
> ~/srsLTE/build/lib/examples$ *./cell_search -b 20*
> < ... >
> Uploading DC/IQ calibration firmware
> -- L
> MCU Ref. clock: 30.72 MHz
> MCU algorithm time: 215 ms
> *Error code 0x1 was returned during streaming. Aborting.*
> *Error code 0x1 was returned during streaming. Aborting.*
>
>
> ~/srsLTE/build/srsue/src$ *sudo ./srsue ue.conf.example*
> < ... >
> Rx calibration using RSSI INTERNAL ON BOARD loopback
> Rx ch.A @ 2685 MHz, BW: 30 MHz, RF input: LNAL, PGA: 20, LNA: 15, TIA: 3
> Rx calibration: using cached values
> Rx calibration values found in cache:
> | DC | GAIN | PHASE
> ---+-----+------+------
> I: | 0 | 2047 | 0
> Q: | 0 | 2047 |
>
> *Searching for cell...*
> *Searching for cell...*
>
> On Thu, Jul 6, 2017 at 7:13 AM, <srslte-users-request at lists.
> softwareradiosystems.com> wrote:
>
>> Send srslte-users mailing list submissions to
>>         srslte-users at lists.softwareradiosystems.com
>>
>> To subscribe or unsubscribe via the World Wide Web, visit
>>         http://www.softwareradiosystems.com/mailman/listinfo/srslte-users
>> or, via email, send a message with subject or body 'help' to
>>         srslte-users-request at lists.softwareradiosystems.com
>>
>> You can reach the person managing the list at
>>         srslte-users-owner at lists.softwareradiosystems.com
>>
>> When replying, please edit your Subject line so it is more specific
>> than "Re: Contents of srslte-users digest..."
>>
>> Today's Topics:
>>
>>    1. Re: limeSDR (Johann T.)
>>
>>
>> ---------- Forwarded message ----------
>> From: "Johann T." <johann.tzt at gmail.com>
>> To: Justin Tallon <justin.tallon at softwareradiosystems.com>
>> Cc: srslte-users at lists.softwareradiosystems.com
>> Bcc:
>> Date: Thu, 6 Jul 2017 16:20:47 +0200
>> Subject: Re: [srslte-users] limeSDR
>> Hi Justin,
>>
>> The SoapySDRUtil was not available. I guess I haven't fully installed the
>> SoapySDR. I only ran "sudo apt-get install libsoapysdr-dev". My bad,
>> sorry!
>>
>> It worked fine after I ran this command:
>>
>> sudo apt-get install soapysdr soapysdr-module-lms7
>>
>> Here is the output of SoapySDRUtil --find
>>
>> tno at snowwhite:~/test/srsLTE/build/lib/examples$ SoapySDRUtil --find
>> ######################################################
>> ## Soapy SDR -- the SDR abstraction library
>> ######################################################
>>
>> Found device 0
>>   addr = 1d50:6108
>>   driver = lime
>>   label = LimeSDR-USB [USB 3.0] 9062000C50C0D
>>   media = USB 3.0
>>   module = STREAM
>>   name = LimeSDR-USB
>>   serial = 0009062000C50C0D
>>
>> I could run the cell_search now, but the output was not as expected.
>> There is an error while calling srslte_ue_sync_work(). Any ideas what went
>> wrong?
>>
>> Thanks,
>> Johann
>>
>>
>>
>> ------------------------------------------------------------
>> --------------------------------------------------------
>>
>> tno at snowwhite:~/test/srsLTE/build/lib/examples$ ./cell_search -b 20
>> linux; GNU C++ version 5.4.0 20160609; Boost_105800;
>> UHD_003.010.001.001-release
>>
>> Opening RF device...
>> Opening USRP with args:
>> Error opening UHD: code 11
>> Soapy Has Found device #0: addr=1d50:6108, driver=lime, label=LimeSDR-USB
>> [USB 3.0] 9062000C50C0D, media=USB 3.0, module=STREAM, name=LimeSDR-USB,
>> serial=0009062000C50C0D,
>> [INFO] Make connection: 'LimeSDR-USB [USB 3.0] 9062000C50C0D'
>> [INFO] Estimated reference clock 30.7197 MHz
>> [INFO] Selected reference clock 30.720 MHz
>> [INFO] Device name: LimeSDR-USB
>> [INFO] Reference: 30.72 MHz
>> [INFO] Init LMS7002M(0)
>> [INFO] LMS7002M cache /home/tno/.limesuite/LMS7002M_cache_values.db
>> [INFO] Ver=7, Rev=1, Mask=1
>> [INFO] LMS7002M calibration values caching Enable
>> CGEN: Freq=80 MHz, VCO=2.56 GHz, INT=82, FRAC=349525, DIV_OUTCH_CGEN=15
>> M=156, N=3, Fvco=1040.000 MHz
>> 16: FE AF AA
>> 16: AA AA 7C
>> phase: min 26.0; max 197.3; selected 111.6)
>> M=156, N=3, Fvco=1040.000 MHz
>> M=182, N=7, Fvco=1040.000 MHz
>> 16: AA 5A 75
>> 16: AA 52 D5
>> phase: min 10.4; max 176.5; selected 93.5)
>> M=182, N=7, Fvco=1040.000 MHz
>> M=156, N=3, Fvco=1040.000 MHz
>> 16: FE AF AA
>> 16: AA AA 3C
>> phase: min 26.0; max 197.3; selected 111.6)
>> M=156, N=3, Fvco=1040.000 MHz
>> M=156, N=3, Fvco=1040.000 MHz
>> 16: 57 AD 3B
>> 16: 26 DC 3D
>> 19: AA 5A 75
>> 16: AA 52 D5
>> phase: min 20.8; max 176.5; selected 98.7)
>> M=156, N=3, Fvco=1040.000 MHz
>> [INFO] Rx Filter calibrated from cache
>> [INFO] Tx Filter calibrated from cache
>> M=156, N=3, Fvco=1040.000 MHz
>> phase: min 5.2; max 360.0; selected 182.6)
>> M=156, N=3, Fvco=1040.000 MHz
>> M=182, N=7, Fvco=1040.000 MHz
>> phase: min 5.2; max 360.0; selected 182.6)
>> M=182, N=7, Fvco=1040.000 MHz
>> M=156, N=3, Fvco=1040.000 MHz
>> phase: min 5.2; max 360.0; selected 182.6)
>> M=156, N=3, Fvco=1040.000 MHz
>> M=156, N=3, Fvco=1040.000 MHz
>> phase: min 5.2; max 360.0; selected 182.6)
>> M=156, N=3, Fvco=1040.000 MHz
>> [INFO] Rx Filter calibrated from cache
>> [INFO] Tx Filter calibrated from cache
>> SetFrequency using cache values vco:1, csw:206
>> TODO: implement rf_soapy_rx_wait_lo_locked()
>> [  0/299]: EARFCN 6150 Freq. 791.00 MHz looking for PSS.
>> Using Volk machine: avx2_64_mmx_orc
>> CGEN: Freq=245.76 MHz, VCO=2.4576 GHz, INT=79, FRAC=0, DIV_OUTCH_CGEN=4
>> ############################################################
>> Rx calibration using RSSI INTERNAL ON BOARD loopback
>> Rx ch.A @  791 MHz, BW: 30 MHz, RF input: LNAL, PGA: 31, LNA: 15, TIA: 3
>> Rx calibration: using cached values
>> Rx calibration values found in cache:
>>    | DC  | GAIN | PHASE
>> ---+-----+------+------
>> I: |   0 | 2047 | 0
>> Q: |   0 | 2047 |
>> ############################################################
>> SetFrequency using cache values vco:1, csw:206
>> TODO: implement rf_soapy_rx_wait_lo_locked()
>> [  1/299]: EARFCN 6151 Freq. 791.10 MHz looking for PSS.
>> ############################################################
>> Rx calibration using RSSI INTERNAL ON BOARD loopback
>> Rx ch.A @ 791.1 MHz, BW: 30 MHz, RF input: LNAL, PGA: 31, LNA: 15, TIA: 3
>> Rx calibration: using cached values
>> Rx calibration values found in cache:
>>    | DC  | GAIN | PHASE
>> ---+-----+------+------
>> I: |   0 | 2047 | 0
>> Q: |   0 | 2047 |
>> ############################################################
>> Rx pktLoss: ts diff: 17680  pktLoss: 12
>> SetFrequency using cache values vco:1, csw:206
>> TODO: implement rf_soapy_rx_wait_lo_locked()
>> [  2/299]: EARFCN 6152 Freq. 791.20 MHz looking for PSS.
>> ############################################################
>> Rx calibration using RSSI INTERNAL ON BOARD loopback
>> Rx ch.A @ 791.2 MHz, BW: 30 MHz, RF input: LNAL, PGA: 31, LNA: 15, TIA: 3
>> Rx calibration: using cached values
>> Rx calibration values found in cache:
>>    | DC  | GAIN | PHASE
>> ---+-----+------+------
>> I: |   0 | 2047 | 0
>> Q: |   0 | 2047 |
>> ############################################################
>> Rx pktLoss: ts diff: 20400  pktLoss: 14
>> SetFrequency using cache values vco:1, csw:206
>> TODO: implement rf_soapy_rx_wait_lo_locked()
>> [  3/299]: EARFCN 6153 Freq. 791.30 MHz looking for PSS.
>> ############################################################
>> Rx calibration using RSSI INTERNAL ON BOARD loopback
>> Rx ch.A @ 791.3 MHz, BW: 30 MHz, RF input: LNAL, PGA: 31, LNA: 15, TIA: 3
>> Rx calibration: using cached values
>> Rx calibration values found in cache:
>>    | DC  | GAIN | PHASE
>> ---+-----+------+------
>> I: |   0 | 2047 | 0
>> Q: |   0 | 2047 |
>> ############################################################
>> Rx pktLoss: ts diff: 20400  pktLoss: 14
>> SetFrequency using cache values vco:1, csw:206
>> TODO: implement rf_soapy_rx_wait_lo_locked()
>> [  4/299]: EARFCN 6154 Freq. 791.40 MHz looking for PSS.
>> ############################################################
>> Rx calibration using RSSI INTERNAL ON BOARD loopback
>> Rx ch.A @ 791.4 MHz, BW: 30 MHz, RF input: LNAL, PGA: 31, LNA: 15, TIA: 3
>> Rx calibration: using cached values
>> Rx calibration values found in cache:
>>    | DC  | GAIN | PHASE
>> ---+-----+------+------
>> I: |   0 | 2047 | 0
>> Q: |   0 | 2047 |
>> ############################################################
>> [INFO] L 1447040
>> Rx pktLoss: ts diff: 20400  pktLoss: 14
>> SetFrequency using cache values vco:1, csw:206
>> TODO: implement rf_soapy_rx_wait_lo_locked()
>> [  5/299]: EARFCN 6155 Freq. 791.50 MHz looking for PSS.
>> ############################################################
>> Rx calibration using RSSI INTERNAL ON BOARD loopback
>> Rx ch.A @ 791.5 MHz, BW: 30 MHz, RF input: LNAL, PGA: 31, LNA: 15, TIA: 3
>> Rx calibration: using cached values
>> Rx calibration values found in cache:
>>    | DC  | GAIN | PHASE
>> ---+-----+------+------
>> I: |   0 | 2047 | 0
>> Q: |   0 | 2047 |
>> ############################################################
>> Rx pktLoss: ts diff: 20400  pktLoss: 14
>> Rx: 5.500 MB/s
>> TODO: implement rf_soapy_rx_wait_lo_locked()
>> [  6/299]: EARFCN 6156 Freq. 791.60 MHz looking for PSS.
>> ############################################################
>> Rx calibration using RSSI INTERNAL ON BOARD loopback
>> Rx ch.A @ 791.6 MHz, BW: 30 MHz, RF input: LNAL, PGA: 31, LNA: 15, TIA: 3
>> Performed by: MCU
>> ------------------------------------------------------------
>> MCU algorithm time: 10 ms
>> Current MCU firmware: 127, unknown
>> Uploading DC/IQ calibration firmware
>> MCU programming : 16384/16384
>> MCU Programming finished, 827 ms
>> MCU Ref. clock: 30.72 MHz
>> Rx: 0.589 MB/s
>> MCU algorithm time: 208 ms
>> Rx: 0.066 MB/s
>> Rx: 0.000 MB/s
>> Error receiving samples
>> Error calling srslte_ue_sync_work()
>> Rx: 0.000 MB/s
>> Error receiving samples
>> Error calling srslte_ue_sync_work()
>> Rx: 0.000 MB/s
>> Error receiving samples
>> Error calling srslte_ue_sync_work()
>> TODO: implement rf_soapy_rx_wait_lo_locked()
>> [  7/299]: EARFCN 6157 Freq. 791.70 MHz looking for PSS.
>> ############################################################
>> Rx calibration using RSSI INTERNAL ON BOARD loopback
>> Rx ch.A @ 791.7 MHz, BW: 30 MHz, RF input: LNAL, PGA: 31, LNA: 15, TIA: 3
>> Performed by: MCU
>> ------------------------------------------------------------
>> MCU algorithm time: 1 ms
>> Current MCU firmware: 3, DC/IQ calibration full
>> MCU Ref. clock: 30.72 MHz
>> MCU algorithm time: 208 ms
>> Rx pktLoss: ts diff: 34000  pktLoss: 24
>> Rx pktLoss: ts diff: 2129760  pktLoss: 1565
>> Rx: 0.426 MB/s
>> ^CSIGINT received. Exiting...
>> Rx: 0.000 MB/s
>> Error receiving samples
>> Error calling srslte_ue_sync_work()
>> Rx: 0.000 MB/s
>> Error receiving samples
>> Error calling srslte_ue_sync_work()
>>
>>
>> Found 0 cells
>>
>> Bye
>>
>>
>>
>>
>> On Thu, Jul 6, 2017 at 3:49 PM, Justin Tallon <
>> justin.tallon at softwareradiosystems.com> wrote:
>>
>>> Hey Johann!
>>>
>>> Could you try run  :
>>>
>>> SoapySDRUtil --find
>>>
>>> from your command line and see if it finds your device?
>>>
>>> Regards,
>>> Justin
>>>
>>> ____
>>> Justin Tallon Ph.D.
>>>
>>> Software Radio Systems (SRS)
>>> http://www.softwareradiosystems.com
>>>
>>> +353-86-067-0753 <+353%2086%20067%200753> |
>>> justin.tallon at softwareradiosystems.com
>>>
>>> On Thu, Jul 6, 2017 at 1:42 PM, Johann T. <johann.tzt at gmail.com> wrote:
>>>
>>>> Hi Justin,
>>>>
>>>> Thanks for your quick response.
>>>>
>>>> I attached here the output from the cmake. It seemed that the soapySDR
>>>> module was properly detected.
>>>>
>>>> Regards,
>>>> Johann
>>>>
>>>>
>>>>
>>>> On Thu, Jul 6, 2017 at 11:13 AM, Justin Tallon <
>>>> justin.tallon at softwareradiosystems.com> wrote:
>>>>
>>>>> Hey Johann!
>>>>>
>>>>> Could you possibly delete CMakeCache.txt from your build directory and
>>>>> run cmake again and send me the terminal output?
>>>>>
>>>>> Thanks!
>>>>> Justin
>>>>>
>>>>> ____
>>>>> Justin Tallon Ph.D.
>>>>>
>>>>> Software Radio Systems (SRS)
>>>>> http://www.softwareradiosystems.com
>>>>>
>>>>> +353-86-067-0753 <+353%2086%20067%200753> |
>>>>> justin.tallon at softwareradiosystems.com
>>>>>
>>>>> On Thu, Jul 6, 2017 at 9:56 AM, Johann T. <johann.tzt at gmail.com>
>>>>> wrote:
>>>>>
>>>>>> Hi,
>>>>>>
>>>>>> Previously I have used srslte with USRP B210 and it worked perfectly.
>>>>>> I have just received my limeSDR and I would like to use srslte with it.
>>>>>>
>>>>>> I have followed the installation procedures as described in this
>>>>>> thread. The cmake and make were completed without errors and the
>>>>>> libSoapySDR.so is there in the /usr/lib/x86_64-linux-gnu/ folder.
>>>>>> However, when I started the cell_search example, it complained that no
>>>>>> compatible device was found.
>>>>>>
>>>>>> Any suggestions what could be the issue? Do I need to change
>>>>>> something in the code?
>>>>>>
>>>>>> Many thanks!
>>>>>>
>>>>>> Regards,
>>>>>> Johann
>>>>>>
>>>>>> PS: Both examples from the LimeSuiteGUI worked fine and my machine is
>>>>>> running Ubuntu 16.04.
>>>>>>
>>>>>>
>>>>>> On Wed, Jun 14, 2017 at 5:20 PM, Justin Tallon <
>>>>>> justin.tallon at softwareradiosystems.com> wrote:
>>>>>>
>>>>>>> no problem!
>>>>>>>
>>>>>>> Justin
>>>>>>>
>>>>>>> ____
>>>>>>> Justin Tallon Ph.D.
>>>>>>>
>>>>>>> Software Radio Systems (SRS)
>>>>>>> http://www.softwareradiosystems.com
>>>>>>>
>>>>>>> +353-86-067-0753 <+353%2086%20067%200753> |
>>>>>>> justin.tallon at softwareradiosystems.com
>>>>>>>
>>>>>>> On Wed, Jun 14, 2017 at 4:20 PM, Nicola Bui <nicola.bui at imdea.org>
>>>>>>> wrote:
>>>>>>>
>>>>>>>> You are right. It worked.
>>>>>>>> I was looking for soapysdr-dev, that's why I could not find it.
>>>>>>>>
>>>>>>>> Thanks,
>>>>>>>>
>>>>>>>> Nicola Bui
>>>>>>>>
>>>>>>>> Research Engineer
>>>>>>>> IMDEA Networks Institute
>>>>>>>> Av. Mar del Mediterraneo, 22
>>>>>>>> 28918 - Leganés (Madrid) - Spain
>>>>>>>> mobile: +34 657 633 987 <+34%20657%2063%2039%2087>
>>>>>>>> phone: +34 91 481 6986 <+34%20914%2081%2069%2086>
>>>>>>>> fax: +34 481 6965
>>>>>>>>
>>>>>>>> On Wed, Jun 14, 2017 at 11:17 AM, Justin Tallon <
>>>>>>>> justin.tallon at softwareradiosystems.com> wrote:
>>>>>>>>
>>>>>>>>> Cool,
>>>>>>>>>
>>>>>>>>> Could you try run
>>>>>>>>>
>>>>>>>>> sudo apt-get install libsoapysdr-dev
>>>>>>>>>
>>>>>>>>> and then delete your CMakeCache.txt file from your build folder
>>>>>>>>> and re run cmake ?
>>>>>>>>>
>>>>>>>>> Thanks!
>>>>>>>>>
>>>>>>>>> Justin
>>>>>>>>>
>>>>>>>>>
>>>>>>>>> ____
>>>>>>>>> Justin Tallon Ph.D.
>>>>>>>>>
>>>>>>>>> Software Radio Systems (SRS)
>>>>>>>>> http://www.softwareradiosystems.com
>>>>>>>>>
>>>>>>>>> +353-86-067-0753 <+353%2086%20067%200753> |
>>>>>>>>> justin.tallon at softwareradiosystems.com
>>>>>>>>>
>>>>>>>>> On Wed, Jun 14, 2017 at 4:15 PM, Nicola Bui <nicola.bui at imdea.org>
>>>>>>>>> wrote:
>>>>>>>>>
>>>>>>>>>> Here you are:
>>>>>>>>>>
>>>>>>>>>> sudo add-apt-repository -y ppa:myriadrf/drivers
>>>>>>>>>> sudo apt-get update
>>>>>>>>>> sudo apt-get install limesuite limesuite-udev limesuite-images
>>>>>>>>>> sudo apt-get install soapysdr soapysdr-module-lms7
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>> Nicola Bui
>>>>>>>>>>
>>>>>>>>>> Research Engineer
>>>>>>>>>> IMDEA Networks Institute
>>>>>>>>>> Av. Mar del Mediterraneo, 22
>>>>>>>>>> 28918 - Leganés (Madrid) - Spain
>>>>>>>>>> mobile: +34 657 633 987 <+34%20657%2063%2039%2087>
>>>>>>>>>> phone: +34 91 481 6986 <+34%20914%2081%2069%2086>
>>>>>>>>>> fax: +34 481 6965
>>>>>>>>>>
>>>>>>>>>> On Wed, Jun 14, 2017 at 11:13 AM, Justin Tallon <
>>>>>>>>>> justin.tallon at softwareradiosystems.com> wrote:
>>>>>>>>>>
>>>>>>>>>>> I believe that there is also meant to be a libSoapySDR.so file
>>>>>>>>>>> present alongside them.
>>>>>>>>>>>
>>>>>>>>>>> Can you recall all the apt-get commands that you have used to
>>>>>>>>>>> install Soapy?
>>>>>>>>>>>
>>>>>>>>>>>
>>>>>>>>>>> ____
>>>>>>>>>>> Justin Tallon Ph.D.
>>>>>>>>>>>
>>>>>>>>>>> Software Radio Systems (SRS)
>>>>>>>>>>> http://www.softwareradiosystems.com
>>>>>>>>>>>
>>>>>>>>>>> +353-86-067-0753 <+353%2086%20067%200753> |
>>>>>>>>>>> justin.tallon at softwareradiosystems.com
>>>>>>>>>>>
>>>>>>>>>>> On Wed, Jun 14, 2017 at 4:09 PM, Nicola Bui <
>>>>>>>>>>> nicola.bui at imdea.org> wrote:
>>>>>>>>>>>
>>>>>>>>>>>> Yes, it is. But the name is libSoapySDR.so.0.6 or
>>>>>>>>>>>> libSoapySDR.so.0.6.0.
>>>>>>>>>>>> Is it just a bad link?
>>>>>>>>>>>>
>>>>>>>>>>>> Nicola Bui
>>>>>>>>>>>>
>>>>>>>>>>>> Research Engineer
>>>>>>>>>>>> IMDEA Networks Institute
>>>>>>>>>>>> Av. Mar del Mediterraneo, 22
>>>>>>>>>>>> 28918 - Leganés (Madrid) - Spain
>>>>>>>>>>>> mobile: +34 657 633 987 <+34%20657%2063%2039%2087>
>>>>>>>>>>>> phone: +34 91 481 6986 <+34%20914%2081%2069%2086>
>>>>>>>>>>>> fax: +34 481 6965
>>>>>>>>>>>>
>>>>>>>>>>>> On Wed, Jun 14, 2017 at 11:06 AM, Justin Tallon <
>>>>>>>>>>>> justin.tallon at softwareradiosystems.com> wrote:
>>>>>>>>>>>>
>>>>>>>>>>>>> Hey Nicola!
>>>>>>>>>>>>>
>>>>>>>>>>>>> Can you confirm that the libSoapySDR.so is present in your
>>>>>>>>>>>>> /usr/lib/ or /usr/lib/x86_64-linux-gnu/ folder ?
>>>>>>>>>>>>>
>>>>>>>>>>>>> I would not recommend installing source versions on top of
>>>>>>>>>>>>> binary installations as this can cause conflicts that produce problems down
>>>>>>>>>>>>> the line.
>>>>>>>>>>>>>
>>>>>>>>>>>>> Justin
>>>>>>>>>>>>>
>>>>>>>>>>>>> ____
>>>>>>>>>>>>> Justin Tallon Ph.D.
>>>>>>>>>>>>>
>>>>>>>>>>>>> Software Radio Systems (SRS)
>>>>>>>>>>>>> http://www.softwareradiosystems.com
>>>>>>>>>>>>>
>>>>>>>>>>>>> +353-86-067-0753 <+353%2086%20067%200753> |
>>>>>>>>>>>>> justin.tallon at softwareradiosystems.com
>>>>>>>>>>>>>
>>>>>>>>>>>>> On Wed, Jun 14, 2017 at 3:57 PM, Nicola Bui <
>>>>>>>>>>>>> nicola.bui at imdea.org> wrote:
>>>>>>>>>>>>>
>>>>>>>>>>>>>> Hi,
>>>>>>>>>>>>>>
>>>>>>>>>>>>>> I installed soapy, too.
>>>>>>>>>>>>>> The cmake log is attached.
>>>>>>>>>>>>>>
>>>>>>>>>>>>>> Thanks,
>>>>>>>>>>>>>>
>>>>>>>>>>>>>> Nicola Bui
>>>>>>>>>>>>>>
>>>>>>>>>>>>>> Research Engineer
>>>>>>>>>>>>>> IMDEA Networks Institute
>>>>>>>>>>>>>> Av. Mar del Mediterraneo, 22
>>>>>>>>>>>>>> 28918 - Leganés (Madrid) - Spain
>>>>>>>>>>>>>> mobile: +34 657 633 987 <+34%20657%2063%2039%2087>
>>>>>>>>>>>>>> phone: +34 91 481 6986 <+34%20914%2081%2069%2086>
>>>>>>>>>>>>>> fax: +34 481 6965
>>>>>>>>>>>>>>
>>>>>>>>>>>>>> On Wed, Jun 14, 2017 at 10:50 AM, Justin Tallon <
>>>>>>>>>>>>>> justin.tallon at softwareradiosystems.com> wrote:
>>>>>>>>>>>>>>
>>>>>>>>>>>>>>> Hey Nicola!
>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>> Could you post the output of your cmake ?
>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>> Thanks!
>>>>>>>>>>>>>>> Justin
>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>> On 14 Jun 2017 5:41 p.m., "Nicola Bui" <nicola.bui at imdea.org>
>>>>>>>>>>>>>>> wrote:
>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>> Dear all,
>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>> I am trying to make srsLTE work with LimeSDR, but cmake
>>>>>>>>>>>>>>>> does not find the LimeSuite package.
>>>>>>>>>>>>>>>> I am running it on a ubuntu 16.04 pc, limesuite is
>>>>>>>>>>>>>>>> installed and I correctly went through the tutorial examples of the
>>>>>>>>>>>>>>>> LimeSuiteGui (both the selfloop and the reception).
>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>> Any suggestions before I am trying installing limesuite
>>>>>>>>>>>>>>>> from the sources?
>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>> Thanks,
>>>>>>>>>>>>>>>> Nicola Bui
>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>> Research Engineer
>>>>>>>>>>>>>>>> IMDEA Networks Institute
>>>>>>>>>>>>>>>> Av. Mar del Mediterraneo, 22
>>>>>>>>>>>>>>>> 28918 - Leganés (Madrid) - Spain
>>>>>>>>>>>>>>>> mobile: +34 657 633 987 <+34%20657%2063%2039%2087>
>>>>>>>>>>>>>>>> phone: +34 91 481 6986 <+34%20914%2081%2069%2086>
>>>>>>>>>>>>>>>> fax: +34 481 6965
>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>> _______________________________________________
>>>>>>>>>>>>>>>> srslte-users mailing list
>>>>>>>>>>>>>>>> srslte-users at lists.softwareradiosystems.com
>>>>>>>>>>>>>>>> http://www.softwareradiosystem
>>>>>>>>>>>>>>>> s.com/mailman/listinfo/srslte-users
>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>
>>>>>>>>>>>>>
>>>>>>>>>>>>
>>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>
>>>>>>>>
>>>>>>>
>>>>>>> _______________________________________________
>>>>>>> srslte-users mailing list
>>>>>>> srslte-users at lists.softwareradiosystems.com
>>>>>>> http://www.softwareradiosystems.com/mailman/listinfo/srslte-users
>>>>>>>
>>>>>>>
>>>>>>
>>>>>> _______________________________________________
>>>>>> srslte-users mailing list
>>>>>> srslte-users at lists.softwareradiosystems.com
>>>>>> http://www.softwareradiosystems.com/mailman/listinfo/srslte-users
>>>>>>
>>>>>>
>>>>>
>>>>
>>>
>>
>> _______________________________________________
>> srslte-users mailing list
>> srslte-users at lists.softwareradiosystems.com
>> http://www.softwareradiosystems.com/mailman/listinfo/srslte-users
>>
>>
>
> _______________________________________________
> srslte-users mailing list
> srslte-users at lists.softwareradiosystems.com
> http://www.softwareradiosystems.com/mailman/listinfo/srslte-users
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://www.softwareradiosystems.com/pipermail/srslte-users/attachments/20170707/ea07cb3d/attachment-0001.html>


More information about the srslte-users mailing list